Zephyrproject CVEs & Vulnerabilities

mcumgr_serial_process_frag() in subsys/mgmt/mcumgr/transport/src/serial_util.c calls net_buf_reset() on the result of smp_packet_alloc() before checking it for NULL. smp_packet_alloc() uses net_buf_alloc(K_NO_WAIT) against the shared MCUmgr packet pool (CONFIG_MCUMGR_TRANSPORT_NETBUF_COUNT, default 4), which returns NULL when the pool is exhausted. In default builds the __ASSERT_NO_MSG in net_buf_reset is a no-op, so net_buf_simple_reset writes through the NULL pointer (buf->len = 0; buf->data = buf->__buf), causing a fault/crash. The fragment data reaches this code from attacker-controlled bytes on the MCUmgr serial/UART/shell-console transports (smp_uart.c, smp_raw_uart.c, smp_shell.c), and a fresh buffer is allocated at the start of essentially every new packet. An attacker on the serial/console link can flood the transport to drive the 4-entry buffer pool to exhaustion and induce the NULL dereference, crashing the device (denial of service). The defect was introduced after the original MCUmgr rework and shipped in Zephyr v4.4.0. The fix moves the NULL check ahead of net_buf_reset.

The USB CDC-NCM device class (subsys/usb/device_next/class/usbd_cdc_ncm.c) ignores the return value of usbd_ep_enqueue() in its ethernet transmit callback cdc_ncm_send(). When the enqueue fails, the function still calls k_sem_take(&data-sync_sem, K_FOREVER), blocking on a completion semaphore that is only ever signaled from the bulk-IN transfer-completion callback. Because nothing was enqueued, that callback never fires and the calling thread — a shared network traffic-class TX thread — deadlocks permanently while holding the interface TX lock, halting transmission until reboot (and leaking the transmit buffer). The enqueue fails under conditions controlled by the attached USB host: usbd_ep_enqueue() returns -EPERM whenever the bus is suspended (a standard, persistent host operation), and the underlying udc_ep_enqueue() returns -EPERM/-ENODEV on disconnect, bus reset, or endpoint disable. The cdc_ncm_send() guard only checks the DATA_IFACE_ENABLED and IFACE_UP flags, not the suspended state, so a packet transmitted while the host holds the bus suspended reaches the failing enqueue and deadlocks the TX path. The realistic trigger is a bus suspend that occurs while the exported network interface is active and has traffic to send — host sleep, USB selective/auto-suspend, or hub power management — after which any device-originated packet deadlocks the path, recoverable only by reboot. The impact is a persistent loss of the virtual network connection between the host's NCM interface and the Zephyr device; because the deadlocked thread is a shared traffic-class TX thread, egress on other network interfaces can stall as well. There is no memory corruption or information disclosure. The defect was introduced with the CDC-NCM driver and shipped in releases through v4.4.0; it is fixed by checking the usbd_ep_enqueue() return value and freeing the buffer before the blocking wait.

On Xtensa targets with CONFIG_USERSPACE and CONFIG_XTENSA_MMU, the page-table code (arch/xtensa/core/ptables.c) maintains a global list, xtensa_domain_list, of active memory domains using a list node embedded inside the caller-owned struct k_mem_domain. When a domain is destroyed via k_mem_domain_deinit() - arch_mem_domain_deinit(), the page tables are torn down and domain-arch.ptables is set to NULL, but the domain's node was not removed from xtensa_domain_list. The freed/deinitialized domain therefore remained linked into the global list as a dangling pointer into caller-owned storage that may then be freed or reused. Any subsequent arch_mem_map()/arch_mem_unmap() operation (widely invoked by kernel memory-mapping and demand-paging code) traverses the stale node and dereferences domain-ptables: at minimum a NULL pointer dereference causing a fatal MMU exception (denial of service), and if the k_mem_domain storage has been freed or reused, a use-after-free in which a stale/controlled ptables value is dereferenced and written through during the page-table walk (l2_page_table_map writes l1_table[...] and l2_table[...], and xtensa_mmu_compute_domain_regs writes into the domain struct and the L1 table), yielding page-table memory corruption that can undermine userspace isolation. The vulnerable path is reachable only from privileged kernel/supervisor code (k_mem_domain_deinit is not a syscall), not directly from unprivileged user threads or remotely. Affected: Zephyr v4.4.0 (the Xtensa memory-domain de-initialization feature was introduced in commit 3032b58f52d and first shipped in v4.4.0); fixed on main by adding sys_slist_find_and_remove() in arch_mem_domain_deinit(). The Xtensa MPU path is unaffected.

The eswifi socket offload driver copies user-provided payloads into a fixed buffer without checking available space; oversized sends overflow `eswifi->buf`, corrupting kernel memory (CWE-120). Exploit requires local code that can call the socket send API; no remote attacker can reach it directly.

dns_unpack_name() caches the buffer tailroom once and reuses it while appending DNS labels. As the buffer grows, the cached size becomes incorrect, and the final null terminator can be written past the buffer. With assertions disabled (default), a malicious DNS response can trigger an out-of-bounds write when CONFIG_DNS_RESOLVER is enabled.

In preloader, there is a possible read of device unique identifiers due to a logic error. This could lead to local information disclosure, if an attacker has physical access to the device, with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: ALPS10607099; Issue ID: MSV-6118.